Lightbar for XP1000 - RangerForums.net - Polaris Ranger Forum
Full Size Ranger Discussion Talk about the full-size ranger

 2Likes
  • 1 Post By Tom-Layla Brough
  • 1 Post By Tom-Layla Brough
 
LinkBack Thread Tools Search this Thread Display Modes
post #1 of 3 Old 08-11-2019, 11:31 AM Thread Starter
Super Moderator
 
Downeaster's Avatar
 
Join Date: Oct 2010
Location: Western Maine mountains
Posts: 1,848
Lightbar for XP1000

I thought I had already posted this but couldn't find it.. So I will try to do it again.


I accepted to install a 40 inch lightbar on top of a 2018 XP1000. I am not familiar with
the 1000's, but it does have interior lining on the roof and doors. Can the upper lining
be taken down then put back up. I see some tabs that look like push pins but aren't, are
they something that come out easy or will I destroy them taking the lining down>


Under the hood I see the 3 prog post that used to hold the electrical hook up is gone and
a new setup against the dash wall. I would assume all these are Keyed terminals. Where is
the full time post for hook ups?


To install a new Lightbar switch in the dash, does the top of the dash over the light switch
just come off after pulling the two pushpins?



I am asking these questions after only a two minute look at his XP1000, so please bare with
me.

2013 Polaris Ranger 900 XP Camo
Blue Sea #5025 Fuse Block w/Neg. Bus
Seizmik rearview + Side view mirrors
MotoAlliance Firestorm Cab heater w/defrost
MotoAlliance Viper 4000 lb winch 1/4" syn rope
Rockford Fosgate radio and speakers
40 inch led lightbar / Glass windshield, poly rear
27 inch Mud Gear Innova tires / Beast Eyes
Rear EMT bumper / 4 inch lift kit


Ranger put the word laughter in slaughter..
Downeaster is offline  
Sponsored Links
Advertisement
 
post #2 of 3 Old 08-11-2019, 01:04 PM
Slow Poke
 
Tom-Layla Brough's Avatar
 
Join Date: Sep 2018
Posts: 33
The dash comes apart easily, I've got one in loads bits at the minute fitting a heater kit. It's all just plastic poppers...

Headling should have torx screws holding it up, 2 at the front and 2 near the rear, and a line of plastic pushfit grippers on the join, sometimes they break on removal.

Power can come from the front plug in bus bar, or you might have a bus bar in the roof too, do you have any roof powered accessories ie interior light, windscreen wiper etc??

If you wire up from the bonnet bus bar then you can run the wires through the front windscreen pillers keeping it tidy, there's an exit hole near the roof lining.
Downeaster likes this.
Tom-Layla Brough is online now  
post #3 of 3 Old 08-11-2019, 01:06 PM
Slow Poke
 
Tom-Layla Brough's Avatar
 
Join Date: Sep 2018
Posts: 33
Current state of dash disassembly... although I've got the heater matrix in now, and fitted the water unions in for the hoses.
Attached Images
File Type: jpeg IMG-20190809-WA0018_1565546696297.jpeg (1.69 MB, 22 views)
Downeaster likes this.
Tom-Layla Brough is online now  
Reply

  Lower Navigation
Go Back   RangerForums.net - Polaris Ranger Forum > Polaris Ranger Forum > Full Size Ranger Discussion

Thread Tools Search this Thread
Show Printable Version Show Printable Version
Email this Page Email this Page
Search this Thread:

Advanced Search
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome